PRECAUTION FOR BALING PRESS MACHINE-
- Clean the filter from the oil tank with the help of diesel every week
- Give oil to some part of the machine where rotating or sliding take place within 2-3 days like-lock plate and lid plate joining part, whole in bush and shaft
- Always check that scrap never come between lock and door cylinder junction point
- Clean the ac chiller forward part within 3-4 days with the help of blower, start chiller half an hour before starting of the machine
- Adjust or tight the bolt of every cylinder with power in a week if needed
- Check oil tank- oil tank is full of oil all time, chiller machine is always fully immersed in the oil tank
- Use good wire
,for electric motor and AC connection stabilizer
- Before starting machine always sure ejector plate is fully set on its surface and clean the below surface of ejector pressure plate
- Never put extra scrap above the chamber it can harm the machine
Ifwant to cut the scrap always sure not to cut from only one side edge of machine ,putit on both edges side chamber of machine
- Clean ejector whole time to time
,soany leakage can be findeasily
- Clean the machine with dry clothes
Machinealways placed on planesurface notinclined surfaces
- Never switch off the machine in half cycle always switch off the machine in starting moving point.
- ALL machine supplied without electricals(customer have to arrange all necessary item for motor connection at his site)
- Machines are provided with a warranty of one year for any manufacturing defect (excluding rubber electrical parts and pressure gauge as these are bought item from outside) and hydraulic pump six months from the date of invoice.
- However warranty does not cover the machine against any misuse, neglect, poor storage, improper maintenance, and accepts no claim for loading, transportion(by road/rail/sea/air direct or either by saroj engg. works), duty loss or profit, and consequential damages of any type will not be entertained.
- Machine warranty starts from the date of billing.
- Any dues after one month lead to the cancellation of warrantee without any prior notice.
- its customer duty to load its machine on time from company workshop as some of product bought by us warrantee started from the date when we purchased that product from our vendor like – pump,valve,seals,motor etc.
- Shearing Blade – for cutting the access scrap spread over the edges of the chamber during feeding the chamber
- hydraulic hopper system – for putting scrap directly into the chamber(only for jumbo models)
- heat exchanger – to cool down the temperature of hydraulic oil for the continuous working of the machine up to 20-24 hours with same performance
- bale remover – to pull bale out from the chamber without any worker help
- operation – manual/semi-automatic/fully automatic(panel/plc)
- Hydraulic oil
- Electrical – like motor starter,main switch
Our engineer/supervisor will install the machine at your site free of any installation charges and commissioning of the machine at your site exclude of up-down ticket charges(for 2nd ac class),visa(in export) and day-night boarding of engineer(in hotel or lodge),when company engineer visit customer site for commissioning of machine, customer will ensure that all material is available related to machine like-machine condition place, hydraulic oil, machine electrical parts will be fitted by the electrician,shed of machine,arrangement of generator if light is not available, labor is available at the time of machine trial and operator -if any of these materials will not be provided then there is waiting charge of 1000/day will be paid by the customer, any miss behave with engineer may lead to the cancellation of warrantee, any due balance after fifteen days from the date of invoice may lead to the cancellation of warrantee, rest of the services are free for one year warranty period but the customer has to pay for ticket, food, and day-night boarding.
if any problem occurs in the machine then we will do our best to solve the problem but then also there is a solution of the problem will take at least 2-3 days to cover the complaint as its timing depends on the availability of requirement part, engineer and engineer ticket time, etc.
35% advance(accepted cheque, DD and RTGS) and full payment before a loading time of machine(at loading time only RTGS will accept). delivery time of machine condition only valid after full payment. Kindly send your order by fax or e-mail only.
Saroj engineering works reserve the right to recover any loss it suffers as a result of Buyer canceling or amending an order .advance nonrefundable.
If payment is not made in accordance with the agreed terms Saroj engineering works reserves the right to claim interest or a late payment charge at an annual rate of the Prime Lending Rate (PLR) of the Reserve Bank of India + 2% on late payment and additional compensation for debt recovery costs but such rate and compensation shall be capped at the maximum permitted under applicable law.
Please Note : Company reserves the right to introduce any modification & change in specification. Any other clause not mentioned in the offer shall not be binding unless otherwise stated in writing.It is clearly understood and acknowledged by placing an order with us, customer has deemed to have accepted all terms and condition and read it in full.
All matters and disputes are subject to DELHI jurisdiction only.